Wrong Pinout in the PDF documentation for the MINI

[guidol]

Yesterday I received my 2 Deneyap mini SBCs and had a hard start, because the graphical PDF-Documentation of the Pinout was different to the little documentation-paper which did came with my Deneyap mini.

I did try to get the mini to work with SPI half a day, before I checked the marking on the bottomside of the mini

My Mini is the mpv1.0-20210519 and the graphical PDF documentation on the Internet is the v2.1

I edited one of the pictures (MiniPinDiagrami) to match my board (as attachment)
and did create a text-list of the REAL Pinnumbers to the signals.

Maybe an adminstrator could put the actual board-documention (PDFs) to the website, because the textual-documentation at
https://docs.deneyapkart.org/en/
seems to be more accurate (like D4 for MOSI in the SPI-section.

DENEYAP_MINI Real Pinout

D = Digital Pin
A = Analog Input
DA = Analog Output
P = PWM
T = Capacitive-Sensing pins

I2C = SDA, SCL
SPI = MISO, MOSI, SCK/CLK, CS/SS

GPIO0 0 D13 GPKEY BUILTIN_KEY
GPIO8 8 A0 T0
GPIO9 9 A1 T1
GPIO10 10 A2 T2
GPIO11 11 A3 T3
GPIO12 12 A4 T4
GPIO13 13 A5 T5
GPIO16 16 A6
GPIO17 17 D12 DA0
GPIO18 18 D11 DA1
GPIO21 21 D10 CS/SS
GPIO26 26 D9
GPIO33 33 LEDG
GPIO34 34 LEDR
GPIO35 35 LEDB
GPIO36 36 D8 SDA
GPIO37 37 D7 SCL
GPIO38 38 D6 SCK/CLK
GPIO39 39 D5 MISO
GPIO40 40 D4 MOSI
GPIO41 41 D3 P1
GPIO42 42 D2 P0
GPIO43 43 D1
GPIO44 44 D0

[ozgbostan]

Yesterday I received my 2 Deneyap mini SBCs and had a hard start, because the graphical PDF-Documentation of the Pinout was different to the little documentation-paper which did came with my Deneyap mini.

I did try to get the mini to work with SPI half a day, before I checked the marking on the bottomside of the mini

My Mini is the mpv1.0-20210519 and the graphical PDF documentation on the Internet is the v2.1

I edited one of the pictures (MiniPinDiagrami) to match my board (as attachment)
and did create a text-list of the REAL Pinnumbers to the signals.

Maybe an adminstrator could put the actual board-documention (PDFs) to the website, because the textual-documentation at
https://docs.deneyapkart.org/en/
seems to be more accurate (like D4 for MOSI in the SPI-section.

Hi Sir,

Thanks for your comments. We are going to check and update the pinout based on your considerations.

[guidol]

Hi Sir,

Thanks for your comments. We are going to check and update the pinout based on your considerations.

Thanks for checking that
The v2.1 seem to be a 2 months(?) older design than the mpv1.0_20210519

I did get the small instructions-paper mpv1.0_20210519 with my Deneyap Mini.
I think this should actually (in original size) downloadable from the Webpage (or both versions)

[guidol]

Hi Sir,
Thanks for your comments. We are going to check and update the pinout based on your considerations.

found another "pinout-problem"

in the files pins_arduino.h and deneyap.h for the mini is defined
(and here: https://docs.deneyapkart.org/en/#pin-tanimlamalari-dym )
GPIO43 D1 TX
GPIO44 D0 RX

but on the graphical .PDF for the mpv1.0 - 20210519 its pictured as
GPIO43 D1 RX
GPIO44 D0 TX

I think the 2 files above are right and the .PDF should also be updated

[do4us]

found another "pinout-problem"

in the files pins_arduino.h and deneyap.h for the mini is defined
(and here: https://docs.deneyapkart.org/en/#pin-tanimlamalari-dym )
GPIO43 D1 TX
GPIO44 D0 RX

but on the graphical .PDF for the mpv1.0 - 20210519 its pictured as
GPIO43 D1 RX
GPIO44 D0 TX

I think the 2 files above are right and the .PDF should also be updated

You are right. There is a fault at the small instructions paper. Please, use this pinout and find out detailed info at here. Thanks for your contribution.

[guidol]

I also created this pinout-picture of the newer mini-pcb